Zte ZXMW NR8250 Manual Download Page 112

Page: 112 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Handling Procedure

Check the link status and find out whether the link is blocked in one direction.

3.25 134243745 Timeout for receiving OSPF hello

packet

Notification Property

Notification Code: 134243745

Notification Information: The alarm is reported when it is timeout for receiving the

Hello packet at the interface where OSPF is implemented.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

The interface to the neighbor is disabled.

Possible Causes

The neighbor does not exist.

The link is interrupted.

The neighbor OSPF interface is down.

Handling Procedure

Check the neighbor status.

3.26 134243746 OSPF interface disabled by

administrator

Notification Property

Notification Code: 134243746

Notification Information: The notification is reported if OSPF interface is disabled due

to management or configuration reason.

Notification Type: Handling Alarm

Sub-code Description

None

3-16

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands