Zte ZXMW NR8250 Manual Download

Page: 29 / 124

Chapter 2 Alarm

2.1.18 134241728 Loopback state in Ethernet port

Alarm Property

Alarm Code: 134241728

Alarm Information: The alarm is reported when the port on RCUB/

RTUM

/RTUH is in

loopback status.

Alarm Level: Major

Alarm Type: Equipment Alarm

Sub-code Description

Sub-code 1: RCUB NMS port;

Sub-code 2: RCUB GbE port;

Sub-code 7: RTUH GbE1 port;

Sub-code 8: RTUH GbE2 port;

Sub-code 9: RTUH GbE3 port;

Sub-code 10: RTUN GbE1 port;

Sub-code 11: RTUN GbE2 port;

Sub-code 12: RTUN GbE3 port;

Sub-code 13: RTUN GbE4 port.

Effect on the System

Traffic is interrupted when the wireless link port is in loopback status.

Possible Causes

The loopback function is enabled for test or maintenance.

The board that reports the alarm is faulty.

Handling Procedure

Select

Maintenance > Port Loopback > ETH

and check whether loopback is

configured for test or maintenance.

If yes, disable the loopback function after the test or maintenance is completed.

If no, replace the faulty board.

If the alarm persists after the preceding step, replace the faulty board.

2.1.19 134243765 1588 clock PTP service setup failure

Alarm Property

Alarm Code: 134243765

Alarm Information: The alarm is reported if the 1588 conversation setup time exceeds

threshold, and the PTP conversation setup failure is reported.

Alarm Level: Major

2-15

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands