Zte ZXMW NR8250 Manual Download Page 33

Page: 33 / 124

Chapter 2 Alarm

If yes, disable the loopback function after the test or maintenance is completed.

(Path:

Maintenance > Radio Port

If no, go to step 2.

Replace the RMU board.

2.1.24 134237782 SNCP route setting alarm

Alarm Property

Alarm Code: 134237782

Alarm Information: The alarm is reported if the SNCP route setting fails.

Alarm Level: Major

Alarm Type: Equipment Alarm

Sub-code Description

None.

Effect on the System

The services using this route are interrupted.

Possible Causes

The system fails to configure the SNCP route.

Handling Procedure

Invalidate the route again.

2.1.25 9001 AC input Switch Off

Alarm Property

Alarm Code: 9001

Alarm Information: AC input switch is off

Alarm Level: Critical

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The rectifier fails to work normally, only the battery can work.

When the battery runs out, the base station is powered down.

2-19

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands