Zte ZXMW NR8250 Manual Download Page 62

Page: 62 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Possible Causes

The description of alarm sub-codes are as follows:

Sub-code 0: ODU failure

Sub-code 1: ODU failure

Sub-code 2: ODU failure

Sub-code 3: ODU failure

Sub-code 4: ODU failure

Sub-code 5: The power of the IF signal sent from IDU to ODU is low.

Sub-code 6: The power of the RF signal received by ODU is low.

Sub-code 7: ODU failure.

Sub-code 8: RMU board or IF cable failure.

Sub-code 9: ODU failure

Sub-code 10: RMU board or IF cable failure.

Sub-code 11: ODU failure

Sub-code 13: RMU board failure

Handling Procedure

Process the sub-codes as follows:

Sub-code 0: Power off and then restart the ODU. If the alarm persists, replace the

ODU.

Sub-code 1: Power off and then restart the ODU. If the alarm persists, replace the

ODU.

Sub-code 2: Power off and then restart the ODU. If the alarm persists, replace the

ODU.

Sub-code 3: Power off and then restart the ODU. If the alarm persists, replace the

ODU.

Sub-code 4: Replace the ODU.

Sub-code 5: Power off and then restart the ODU. If the alarm persists, use a shorter

IF cable.

Sub-code 6: Ensure that the ODU Rx frequency on local site matches ODU Tx

frequency on remote site. If the alarm persists, increase remote ODU transmit power.

If the alarm still remains, replace the ODU.

Sub-code 7: Replace the ODU.

Sub-code 8: Replace the IF cable. If the alarm persists, replace the RMU board.

Sub-code 9: Replace the ODU.

Sub-code 10: Replace the IF cable. If the alarm persists, replace the RMU board.

Sub-code 11: Replace the ODU.

Sub-code 13: Replace the RMU board.

2-48

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands