Zte ZXMW NR8250 Manual Download Page 116

Page: 116 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Effect on the System

The link performance cannot meet the expected configuration requirement.

Possible Causes

The number of errored symbols of the physical layer within the unit time exceeds the

preset threshold.

The number of errored frames of the MAC layer within the unit time exceeds the preset

threshold.

The number of errored frames of MAC layer within the unit frame amount exceeds the

preset threshold.

The number of errored frame seconds of the MAC layer within the unit time exceeds

the preset threshold.

Handling Procedure

Contact the network engineer and optimize the link performance.

3.32 134243774 EFM loopback indication

Notification Property

Notification Code: 134243774

Notification Information:

The notification is reported if EFM performs loopback

indication.

Notification Type: Qos Alarm

Sub-code Description

Sub-code 1: Starting loopback fails;

Sub-code 2: Stopping loopback fails.

Effect on the System

This notification indicates the loopback operation status.

Possible Causes

The system fails to start or stop a loopback.

Handling Procedure

None

3-20

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands