Zte ZXMW NR8250 Manual Download Page 21

Page: 21 / 124

Chapter 2 Alarm

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

This alarm does not affect any traffic, but it may cause device to slow down.

Possible Causes

CPU is overloaded.

Handling Procedure

Delete the traffic that fails to work or restart the equipment.

On the LMT, select

TDM

ETH

and delete the ineffective service. Or, warm start the

equipment.

2.1.9 134218747 RPUA powered off

Alarm Property

Alarm Code: 134218747

Alarm Information: This alarm is reported if no power is supplied to PS port of RPUA

or the power supply is abnormal.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

Sub-code 1: RPUA-PS1 powered off;

Sub-code 2: RPUA-PS2 powered off.

Effect on the System

If RPUA-PS1 and RPUA-PS2 are powered off simultaneously, the ODU will be powered

off and the radio link will be broken.

Possible Causes

PS1 port or PS2 port of the RPUA board is not connected to the power supply.

The RPUA board is faulty.

2-7

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands