Zte ZXMW NR8250 Manual Download

Page: 76 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Possible Causes

The virtual interface configurations at the two ends do not match. The virtual interface

configurations include version number, area configuration, network mask, Hello timer

interval, and Dead timer interval.

Handling Procedure

Ensure that the virtual interface configurations at the two ends match.

2.3.4 2002 Communication link between boards broken

Alarm Property

Alarm Code: 2002

Alarm Information: This alarm is reported when the communication link between pe-

ripheral board and master main control board, or between slave main control board

and master main control board is interrupt.

Alarm Level: Critical

Alarm Type: Handling Alarm

Sub-code Description

None

Effect on the System

The board fails to communicate with the active main-control board, causing that the

services carried by the board are interrupted.

Possible Causes

The board is configured in the network management system but it is not inserted in

the rack.

The link between the board and the active main control board is faulty.

Handling Procedure

Check whether the correct board is inserted into the corresponding slot of the base

station.

If yes, go to step 2.

If no, replace it with a correct one.

The board's link is broken. Cold reset the board. If the alarm persists, go to step 3.

Replace the board.

2-62

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands