Zte ZXMW NR8250 Manual Download Page 79

Page: 79 / 124

Chapter 2 Alarm

Sub-code 3: Failed to load DSP software

Sub-code 4: Failed to download CPU software

Sub-code 5: Failed to download FPGA software

Sub-code 6: Failed to download DSP software

Effect on the System

The services carried by the board are interrupted.

Possible Causes

The board's software version, which is saved in the main control board, is incorrect.

The board is faulty.

Handling Procedure

In the software version management window, select

Maintenance > Version > IDU

and check whether the software version is correct.

If no, download the correct version package.

If yes, go to step 2.

Replace the board.

2.3.8 6206 Running software version fault

Alarm Property

Alarm Code: 6206

Alarm Information: When the main control board detects that the running software

version does not exist, this alarm is reported.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

3145728: RCUA CPU version

3147776: RCUA FPGA version

9503265: RTUA CPU version or RTUB CPU version

9505280: RTUA FPGA version

9503424: RTUM CPU version

9505296: RTUB FPGA version (FUNC=0)

9505297: RTUB FPGA version (FUNC=1)

9568784: RMU CPU version

9570832: RMU FPGA version

9597456: RMU CFG version

Effect on the System

The board cannot obtain the software, and cannot start properly after being reset.

2-65

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands