Zte ZXMW NR8250 Manual Download Page 30

Page: 30 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The conversation connection setup fails, and the opposite-end master clock source of the

conversation cannot be taken as the current synchronization master clock source.

Possible Causes

The PTP configuration is incorrect or the network is abnormal.

Handling Procedure

Ensure that the slave device configurations such as the destination address and PTP

configuration.

Check whether the PTP configuration of the slave device and master device are

correct.

If yes, go to step 2.

If no, modify the PTP configuration, such as the destination address and VLAN

information.

Check the network connections between the slave device and the master device.

2.1.20 134243766 1588 clock PTP link abnormal

Alarm Property

Alarm Code: 134243766

Alarm Information: The alarm is reported if a PTP link has serious packet loss problem.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The 1588 slave clock link detects that the link becomes abnormal due to serious packet loss

problem. The master link alarm may cause 1588 master/slave link changeover. A slave

link that has the alarm is not selected as the link to which the changeover is performed.

Possible Causes

The threshold setting is not reasonable.

Network problems occur, for example, the cable is faulty.

2-16

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands