Zte ZXMW NR8250 Manual Download Page 114

Page: 114 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code Description

None

Effect on the System

Adjacency will be re-build.

Possible Causes

Neighbor IP or RouterID is changed, leading to loss of adjacent relationship.

Handling Procedure

Check new configuration for neighbor's IP or RouterID.

3.29 134243763 The port failing to be aggregated into

a LAG

Notification Property

Notification Code: 134243763

Notification Information:

The notification is reported when the port fails to be

aggregated into a LAG.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

The port is blocked for some time.

Possible Causes

The duplex mode of the LAG member ports is set to half duplex.

The status of the LAG member ports is PhyDown or Admin Down.

Handling Procedure

Check the property configuration of the LAG ports. Ensure that the duplex mode is full

duplex and the port configurations are consistent for the two LAG member devices at

the two ends.

Check the networking configuration and ensure that the aggregation ports are

operating properly.

3-18

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands