Zte ZXMW NR8250 Manual Download Page 84

Page: 84 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

2.4.3 134243761 MSTP port ROOT Guard

Alarm Property

Alarm Code: 134243761

Alarm Information: The alarm is reported if the port is blocked due to the ROOT Guard

function.

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The port is blocked for some time.

Possible Causes

The port configured with ROOT Guard function receives a high-priority configuration

message.

Handling Procedure

Check where the high-level priority BPDU packet comes from, whether the port should be

configured with ROOT Guard function, whether there are network attacks, and whether

the configuration such as bridge priority is correct.

Check whether the bridge whether the port is located is a root bridge.

If yes, go to step 2.

If no, delete the ROOT protection configuration of the port.

Check whether the expected root bridge does not actually serve as the root due to

incorrect network bridge configuration, for example, incorrect network bridge priority.

If yes, modify the configuration.

If no, go to step 3.

Find out the source of the packets with higher priority and check whether network

attack exists. If yes, contact the network engineer.

2.4.4 134257728 IDU overheated

Alarm Property

Alarm Code: 134257728

Alarm Information: The alarm is reported if the working temperature of a board

exceeds the upper limit (80 degree Celsius).

Alarm Level: Warning

Alarm Type: Environment Alarm

2-70

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands