Zte ZXMW NR8250 Manual Download Page 82

Page: 82 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code 4: The standby software package is incorrect

Sub-code 5: The running patch package of standby software package is incorrect

Sub-code 13: The firmware package is incorrect

Sub-code 14: The hot patch package is incorrect

Effect on the System

If the running software package or the running software package’s running patch is

abnormal, it might cause that the corresponding board cannot be powered on properly

after being reset.

The software package containing abnormal version files cannot be activated or

switched.

Service Impact:

If the running software package or the running software package’s running patch

is abnormal, the services will be affected after the board is reset. How much the

services are affected depends on the service importance.

If it is other software package that is abnormal, the service will not be affected.

Possible Causes

If the software version consistency check indicates that the version in software package

does not exist on the disk or is damaged, this alarm is reported.

Handling Procedure

Re-download the software version pacakge.

2.4 Environment Alarm

2.4.1 134243759 MSTP port BPDU Guard

Alarm Property

Alarm Code: 134243759

Alarm Information: The alarm is reported if the port is blocked due to the BPDU Guard

function.

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The port is blocked for some time.

2-68

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands