Zte ZXMW NR8250 Manual Download Page 103

Page: 103 / 124

Chapter 3 Notification

Possible Causes

The changeover fails.

Handling Procedure

None

3.10 10016 Board changeover failure

Notification Property

Notification Code: 10016

Notification Information: The active/standby changeover condition is not satisfied.

Notification Type: Handling Alarm

Sub-code Description

Sub-code 1: The standby board is not in the service status

Sub-code 2: The standby board is abnormal

Sub-code 3: Communication between the active board and the standby board is

abnormal

Sub-code 4: The board is not the active board in hardware

Sub-code 5: The clock status of the standby board is abnormal

Sub-code 6: The interval between two consecutive changeover is less than 5 minutes

Sub-code 7: The network interface status of the standby board is abnormal

Sub-code 8: The version management process forbids changeover

Sub-code 9: The entire table configuration forbids changeover

Effect on the System

The active/standby status of the main control board cannot be modified.

Possible Causes

The changeover is not allowed.

Handling Procedure

Handle the alarm according to the sub-code.

3.11 134243728 LLDP global enable status changed

Notification Property

Notification Code: 134243728

Notification Information: The alarm is reported when the Link Layer Discovery Protocol

(

LLDP

) global enable status is changed.

3-7

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands