Zte ZXMW NR8250 Manual Download Page 70

Page: 70 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Handling Procedure

Check the bandwidth usage and check the Nes on the link.

2.2.41 134243769 EFM local link fault

Alarm Property

Alarm Code: 134243769

Alarm Information: The alarm is reported if link fault is detected at the local end.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Link signal lost at the remote end;

Sub-code 2: Unpredictable event, such as power cutoff;

Sub-code 3: Undefined critical event.

Effect on the System

If the local link is faulty, the service at the port may be disconnected.

Possible Causes

The local end detects link fault.

Handling Procedure

Check the LMT or panel status for the physical connections of the local optical port.

Troubleshoot the ports.

2.2.42 134243770 EFM remote link fault

Alarm Property

Alarm Code: 134243770

Alarm Information: The alarm is reported if the local end detects the link fault

information sent from the remote end.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Link signal lost at the remote end;

Sub-code 2: Unpredictable event, such as power cutoff;

Sub-code 3: Undefined critical event.

2-56

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands