Zte ZXMW NR8250 Manual Download Page 117

Page: 117 / 124

Chapter 3 Notification

3.33 134243777 Local Discovery process reset

Notification Property

Notification Code: 134243777

Notification Information: The notification is reported if EFM restarts the discovery

process.

Notification Type: Qos Alarm

Sub-code Description

None

Effect on the System

EFM state is abnormal.

Possible Causes

The link is connected again and EFM restarts the discovery process.

Handling Procedure

None

3.34 134317731 Configuration file reloaded

Alarm Property

Notification Code: 134317731

Notification Information: The notification is reported if the configuration file is reloaded.

Notification Type: Equipment Alarm

Sub-code Description

Sub-code 2: Loading front-end configuration files fails;

Sub-code 3: Synchronizing back-end whole table configuration files fails.

Effect on the System

This notification affects the service quality. If the configuration file is manually loaded,

the equipment should be restarted. If the configuration file is automatically loaded, the

equipment need not be restarted.

Possible Causes

Loading the entire table fails.

Loading the database fails when the system starts.

3-21

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands