Zte ZXMW NR8250 Manual Download Page 111

Page: 111 / 124

Chapter 3 Notification

3.23 134243743 OSPF interface receiving incorrect DD

packet sequence number

Notification Property

Notification Code: 134243743

Notification Information: The alarm is reported if OSPF interface receives DD packet

that contains incorrect sequence number from the neighbor.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

This alarm may cause LSDB resynchronization.

Possible Causes

The active/standby neigotiation flag or the sequence number is incorrect during DD

exchange.

Handling Procedure

No processing is required.

3.24 134243744 Hello packet received at OSPF interface

does not include the router

Notification Property

Notification Code: 134243744

Notification Information: The alarm is reported when the Hello packet received at the

interface where OSPF is implemented does not include this router.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

The neighbor state machine returns to the initial state (Init).

Possible Causes

The link status is changed.

3-15

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands