Zte ZXMW NR8250 Manual Download Page 65

Page: 65 / 124

Chapter 2 Alarm

Effect on the System

Ethernet traffic at the port where an alarm is reported is interrupted.

Possible Causes

Network cable failure.

Network port failure.

Handling Procedure

Perform Ethernet MAC loopback.

If yes, replace the Ethernet cable.

If no, go to step 2.

Replace the board.

2.2.33 134243751 RMEP CCM packet lost

Alarm Property

Alarm Code: 134243751

Alarm Information: The alarm is reported if LMEP does not receive the CCM packet

of RMEP within 3.5 CCM periods.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board. The purpose is to inform the administrator

that the link may be blocked.

Possible Causes

No MEP is configured at the opposite-end NE.

The bearer layer is faulty.

The network is seriously congested.

Handling Procedure

Check whether the MEP is correctly configured at the opposite end.

If yes, go to step 2.

If no, configure the MEP parameters matching the local end.

Check whether the bearer layer is normal.

If yes, check whether alarms associated with other modules exist and handle

them.

2-51

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands