Zte ZXMW NR8250 Manual Download

Page: 92 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Alarm Level: Minor

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The power to the overcurrent board is turned off and the services carried by this board are

completely interrupted.

Possible Causes

The MP current status of the PM board's load is checked periodically. If over-current is

detected, this alarm is reported.

Handling Procedure

Remove and insert the corresponding board;

Replace the corresponding board;

Replace PM board;

Replace the backplane.

2.4.17 405 PP overcurrented

Alarm Property

Alarm Code: 405

Alarm Information: This alarm is reported when the PP current is out of range and

cleared when the current becomes normal.

Alarm Level: Minor

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The power to the over-current board is turned off and the services provided by this board

are interrupted.

Possible Causes

The PP current status of the PM board's load is checked periodically. If over-current is

detected, this alarm is reported.

2-78

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands