Zte ZXMW NR8250 Manual Download Page 67

Page: 67 / 124

Chapter 2 Alarm

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

None

Handling Procedure

Check the port of the RMEP in the alarm.

2.2.36 134243754 RMEP RDI

Alarm Property

Alarm Code: 134243754

Alarm Information: The alarm is reported if LMEP receives the CCM packet in which

the RDI information is abnormal.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board. It indicates that a section or node of

the link covered in maintenance association (MA) is faulty and some traffic stream will be

interrupted.

Possible Causes

Some MEPs in the same MA has alarms.

Handling Procedure

Check the MEP in alarm in the MA for the alarm type. Remove the fault according to the

alarm type.

2.2.37 134243755 Ethernet devices cross-connected

Alarm Property

Alarm Code: 134243755

Alarm Information: The alarm is reported if LMEP receives the CCM packet from MEP

of other MA.

Alarm Level: Major

2-53

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands