Zte ZXMW NR8250 Manual Download Page 38

Page: 38 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

2.1.31 9007 AC Current Over

Alarm Property

Alarm Code: 9007

Alarm Information: The AC input current is higher than the AC current maximum.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

Over-current for a long time might cause the air break switch of the AC input to break.

The AC input loop might be too hot, and the cable might be aging.

It influences the power supply for the base station.

Possible Causes

The AC input current is larger than the threshold value for the alarm.

The power supply's load is too heavy.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

Handling Procedure

Check the threshold value of the monitoring unit's AC input current;

Check whether the AC input voltage is too low;

Check whether the AC power supply is overloaded;

Check whether the monitoring unit's socket is inserted properly;

Replace the monitoring unit.

2.2 Communication Alarm

2.2.1 134217734 ODU level exceeded

Alarm Property

Alarm Code: 134217734

Alarm Information: The alarm is reported when the ODU level exceeds the specified

threshold.

Alarm Level: Minor

Alarm Type: Communications Alarm

2-24

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands