Zte ZXMW NR8250 Manual Download Page 57

Page: 57 / 124

Chapter 2 Alarm

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Optical port 1 on the RTUB board;

Sub-code 2: Optical port 2 on the RTUB board.

Effect on the System

The receive signal transmitted on the SDH link is interrupted.

Possible Causes

The regenerator section trace identification J0 is incorrect. The actual J0 value is

inconsistent with the preset value.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Ensure that the preset trace identification of VC-4 channel (J0) of the NR8250

upstream equipment is

-ZTE-MW-NR8250-

If yes, go to step 2.

If no, modify the trace identification of VC-4 channel (J0)

-ZTE-MW-NR8250-

The alarm is caused by RTUB board failure. Replace the board.

2.2.26 134237934 E1-AIS

Alarm Property

Alarm Code: 134237934

Alarm Information:

The alarm indicates that every bit of the digital signal is "1".

The alarm is reported if at least 255 consecutive bits in the received signal is "1".

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: E1 port 1 on the panel;

Sub-code 2: E1 port 2 on the panel;

Sub-code 3: E1 port 3 on the panel;

Sub-code 4: E1 port 4 on the panel;

Sub-code 5: E1 port 5 on the panel;

Sub-code 6: E1 port 6 on the panel;

Sub-code 7: E1 port 7 on the panel;

Sub-code 8: E1 port 8 on the panel;

2-43

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands