Zte ZXMW NR8250 Manual Download Page 99

Page: 99 / 124

Chapter 3 Notification

Handling Procedure

None

3.3 10003 PM active-to-standby changeover completed

Notification Property

Notification Code: 10003

Notification Information: The notification is reported when the active-to-standby

changeover is completed.

Notification Type: Equipment Alarm

Sub-code Description

None

Effect on the System

None

Possible Causes

It is the notification of the active-to-standby changeover being completed.

Handling Procedure

None

3.4 10004 PM standby-to- changeover completed

Notification Property

Notification Code: 10004

Notification Information: The notification is reported to indicate that the standby PM

board serves as the active board and the active PM board serves as the standby

board.

Notification Type: Equipment Alarm

Sub-code Description

None

Effect on the System

None

3-3

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands