Zte ZXMW NR8250 Manual Download Page 110

Page: 110 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code Description

None

Effect on the System

This alarm may cause LSDB synchronization failure on virtual link.

Possible Causes

The contents of the DD, LSR, LSAck, and LSU packets are incorrect.

Handling Procedure

No processing is required.

3.22 134243742 OSPF interface receiving incorrect

LSR packet

Notification Property

Notification Code: 134243742

Notification Information: The alarm is reported if OSPF interface receives incorrect

LSR packet from the neighbor.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

This alarm may cause LSDB resynchronization.

Possible Causes

The requested LSA does not exist or the interface does not support the requested LSA

type.

Handling Procedure

No processing is required.

3-14

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands