Zte ZXMW NR8250 Manual Download Page 61

Page: 61 / 124

Chapter 2 Alarm

2.2.29 134239930 RF ODU fault

Alarm Property

Alarm Code: 134239930

Alarm Information: The alarm is reported if the ODU detects a fault.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 0: Tx RF PLL unlocked;

Sub-code 1: Tx IF PLL unlocked;

Sub-code 2: Rx RF PLL unlocked;

Sub-code 3: Rx IF PLL unlocked;

Sub-code 4: ODU TX power power low (3 dB less than target value);

Sub-code 5: TX Cable Loop out of range alarm;

Sub-code 6: ODU RX automatic transmit power gain reaches the maximum;

Sub-code 7: TRX EEPROM alarm;

Sub-code 8: TELEMETRY communication alarm;

Sub-code 9: IFC EEPROM alarm;

Sub-code 10: IDU input signal not detected by ODU;

Sub-code 11: Calibration alarm;

Sub-code 13: IF input signal too high alarm(overpass 3db);

Effect on the System

Sub-codes affect the running of traffic as follows:

Sub-code 0: In protection mode, it leads to switchover between active and standby

traffic units; in non-protection mode, it leads to traffic interruption.

Sub-code 1: In protection mode, it leads to switchover between active and standby

traffic units; in non-protection mode, it leads to traffic interruption.

Sub-code 2: In protection mode, it leads to switchover between active and standby

traffic units; in non-protection mode, it leads to traffic interruption.

Sub-code 3: In protection mode, it leads to switchover between active and standby

traffic units; in non-protection mode, it leads to traffic interruption.

Sub-code 4: It may lead to error codes.

Sub-code 5: It may lead to error codes.

Sub-code 6: It may lead to error codes.

Sub-code 7: It may lead to traffic interruption.

Sub-code 8: It may lead to traffic interruption.

Sub-code 9: It may lead to traffic interruption.

Sub-code 10: ODU forcibly disables power amplifier, which leads to traffic interruption.

Sub-code 11: It may lead to traffic interruption.

Sub-code 12: It will lead to traffic interruption.

Sub-code 13: It may lead to traffic interruption.

2-47

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands