Zte ZXMW NR8250 Manual Download Page 69

Page: 69 / 124

Chapter 2 Alarm

2.2.39 134243757 Link delay exceeding the threshold

Alarm Property

Alarm Code: 134243757

Alarm Information: The alarm is reported if the time of sending the packets from the

source end to the destination end is too long.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

The network is congested or there are too many NEs on the traffic path.

Handling Procedure

Check the bandwidth usage and check the Nes on the link.

2.2.40 134243758 Link delay jitter exceeding the threshold

Alarm Property

Alarm Code: 134243758

Alarm Information: The alarm is reported if the link delay is unstable with too much

jitter.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

The network is congested or there are too many NEs on the traffic path.

2-55

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands