Zte ZXMW NR8250 Manual Download Page 72

Page: 72 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

If no, go to step 4.

On the LMT, check whether the Tunnel bandwidth reaches the maximum limit. If it

does, perform Tunnel capacity expansion or find out the source that illegally transmits

the large amount of data and solve the problem. If the alarm persists, contact the

network engineer.

2.2.44 134243776 EFM local link lost

Alarm Property

Alarm Code: 134243776

Alarm Information: The alarm is reported if heartbeat is lost at the local end and the

remote end of EFM.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

The link is disconnected.

Possible Causes

Heartbeat is lost at the local end and the remote end of EFM.

Handling Procedure

On the LMT, check whether there are alarms related to the optical module or boards.

If yes, remove the faults of the optical module and board.

If no, go to step 2.

On the LMT, check whether the optical fibers or cables are faulty.

If yes, replace the faulty fiber or cable.

If no, go to step 3.

On the LMT, check the OAM parameter setting of NEs at the two ends to see whether

they are consistent.

If yes, modify the OAM parameters at both ends to be consistent.

If no, go to step 4.

On the LMT, check whether the Tunnel bandwidth reaches the maximum limit. If it

does, perform Tunnel capacity expansion or find out the source that illegally transmits

the large amount of data and solve the problem. If the alarm persists, contact the

network engineer.

2-58

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands