Zte ZXMW NR8250 Manual Download Page 77

Page: 77 / 124

Chapter 2 Alarm

2.3.5 6201 Software loading failure

Alarm Property

Alarm Code: 6201

Alarm Information: The alarm is reported when the CPU/DSP/FPGA software fails to

be loaded.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

Sub-code 0: CPU software

Sub-code 1: FPGA software

Effect on the System

The services carried by the board are interrupted.

Possible Causes

The board's software version, which is saved in the main control board, is incorrect.

2The board is faulty.

Handling Procedure

In the software version management window, select

Maintenance > Version > IDU

and check whether the software version is correct.

If no, download the correct version package.

If yes, go to step 2.

Replace the board.

2.3.6 6203 Software version synchronization failure between active

board and standby board

Alarm Property

Alarm Code: 6203

Alarm Information: When the standby main control board fails to synchronize the

software version with that of the active main control board, the alarm is reported.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

Sub-code 1: The active software package synchronization failure

Sub-code 2:

The running patch packge of the active software package

synchronization failure

2-63

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands