YASKAWA H6B1A002, Technical Reference

Page: 510 / 794

6.7 Parameter Setting Errors
510 YASKAWA SIEPYAIH6B01A HV600 AC Drive Bypass Technical Reference
Code Name Causes Possible Solutions
These parameters are set at the same time:
• H1-xx = 62 [Speed Search from Fref]
• H5-22 = 1 [Speed Search from MODBUS =
Enabled]
Remove one of the function settings.
Parameter S3-01 ≠ 0 [PI2 Control Enable Selection ≠
Disabled] and MFDI set for H1-xx = AD [Select PI2
Control PI Parameters] is ON or MFDI set for H1-xx
= 1AD [!Select PI2 Control PI Parameters] is OFF.
•
Set S3-01 = 0 to use H1-xx = AD or 1AD for the adjustments of
S3-06 [PI2 Control Proportional Gain] and S3-07 [PI2 Control
Integral Time] instead of the primary PI controller Proportional
and Integral adjustments.
• When PI2 Control is necessary, remove the MFDI function
setting.
Code Name Causes Possible Solutions
oPE05 Run Cmd/Freq Ref Source Sel Err There is an option card installed on the drive. Remove the option card from the drive. If it is compatible, install
the option card on the bypass control board.
The setting to assign the Run command or frequency
reference to an option card is incorrect. Correct the parameter settings.
Z1-39 = 3 [Drive/Bypass Source Select = Option
PCB]
is set, but there is no option card connected.
b1-01 = 3 [Frequency Reference Selection 1 =
Option PCB]
is set, but there is no option card
connected.
b1-02 = 3 [Run Command Selection 1 = Option
PCB]
is set, but there is no option card connected.
Connect an option card.
When S5-04 = 0 [HAND-OFF-AUTO Behavior =
Legacy] , you set b1-02 ≠ 7, 8, or 9 [Run Command
Selection 1 ≠ AUTO C Term Run, AUTO
C Serial Run, or AUTO C
Option Run]
.
Set b1-02 = 7, 8, or 9 .
When S5-10 = 2 [AUTO Key Memory at Power
Down = AUTO Mode] , you set b1-02 = 0 [Keypad] .
Change the b1-02 or S5-10 setting.
Code Name Causes Possible Solutions
oPE07 Analog Input Selection Error The settings for H3-02 and H3-10 [MFAI Function
Selection] and H7-30 [Virtual Analog Input
Selection] overlap.
Set H3-02, H3-10, and H7-30 correctly to prevent overlap.
Note:
It is possible to set these functions to multiple analog input
terminals at the same time:
•
Setting value 0 [Frequency Reference]
•
Setting values F and 1F [Not Used]
Code Name Causes Possible Solutions
oPE08 Parameter Selection Error You set these parameters:
•
S1-01 = 1 [Dynamic Noise Control = Enabled]
•
Y4-42 ≠ 0 [Output Disconnect Detection Sel ≠
Disabled]
Set S1-01 = 0 or Y4-42 = 0 .
You set L6-02 [Torque Detection Level 1] < L6-14
[Motor Underload Level @ Min Freq] .
Set parameters to be L6-02 ≥ L6-14 .
Code Name Causes Possible Solutions
oPE09 PID Control Selection Fault
These parameters are set at the same time:
• b5-01 = 1
• b5-11 = 1 [PID Output Reverse Selection =
Negative Output Accepted]
And one of these parameters is set:
•
d2-02 ≠ 0.0 [Frequency Reference Lower Limit ≠
0.0%]
• Y1-06 ≠ 0.0 [Minimum Speed ≠ 0.0%]
• Y4-12 ≠ 0.0 [Thrust Frequency ≠ 0.0%]
• YF-01≠ 0 [PI Aux Control Selection ≠ Disabled]
Correct the parameter settings.
Parameter b5-01 = 3 and one of these parameters is
set at the same time:
•
d2-02 ≠ 0.0
•
Y1-06 ≠ 0.0
•
Y4-12 ≠ 0.0
•
YF-01≠ 0
Correct the parameter settings.
Note:
The drive detects this error if the PID control function selection is incorrect.
(When b5-01 = 1 or 3 [PID Mode Setting = Standard or Fref + PID Trim] )