Sample Programs
Reference
3Ć164
The third example illustrates how to perform GONOGO testing and how to
report the result when it fails.
Two programs in which the BETA vs. IC measurements are performed are
shown below. The program \BJT\PRG_BJT3.PRG, performs GONOGO
testing after the measurement is made if BETA within the range from 50 to
150 at 1 mA with respect to the IC. It also makes a hardcopy of the graph on
the disk in TIFF format (in this case, the MEASURE menu should be disĆ
played on the CRT). The other program \BJT\PRG_BJT4, performs GONOĆ
GO testing after the measurement is made if BETA is within the range from
60 to 160 at 10 mA with respect to the IC. It also plots the curves in the
graph.
In each program, measurement and GONOGO testing are performed 20
times, and it assumes that the BJT is exchanged when the program goes
into pause state for each loop.
Execute the program as was done in step 1 through step 5 of Example 1.
Example 3Ć1: PRG_BJT3.PRG
Line No.
Statements
ăĂă
1
MAIN
ăĂă
2
LOAD SETUP GONO_BT1.SET
ăĂă
3
FOR X= 0 19
ăĂă
4
PAUSE
ăĂă
5
SINGLE
ăĂă
6
IF GONOGO == FAIL
ăĂă
7
HARDCOPY DISK TIFF FAIL&X.TIF
ăĂă
8
ENDIF
ăĂă
9
ENDFOR
ăĂ
10
END
Example 3
Summary of Contents for 372
