Stober POSIDYN SDS 5000 Operation Manual Download Page 5

Page: 5 / 196

Table of contents

Operation manual POSIDYN® SDS 5000

ID 442289.06

KEEP

THINGS

MOVING

11.3.5

Exchanging the master position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

11.4

Remote maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

11.4.1

System administration .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

11.4.2

The network and remote service assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

11.4.2.1

The Network tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

11.4.2.2

The Activation remote service tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

11.4.2.3

Internet proxy server tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

11.4.3

Administration of remote maintenance settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

11.4.4

Using the remote maintenance settings of the gateway inverter . . . . . . . . . . . . . 100

11.4.5

Settings for a LAN connection .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

11.4.6

Settings for an internet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

11.4.6.1

Internet settings for POSITool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

11.4.7

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

11.4.8

Activation of remote maintenance .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

11.4.9

Establishment of a connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

11.4.10

Deactivation of remote maintenance .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

11.4.11

Monitoring remote maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

11.4.12

Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

11.4.13

General Terms and Conditions of STÖBER ANTRIEBSTECHNIK GmbH &

Co. KG for maintenance of the servo Inverter of the 5th generation of STOBER

inverters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

12 Service

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

126

12.1 Replacing inverters .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

12.2 Replacing an application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

12.3 Copying Paramodule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

12.4 Live firmware update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

12.4.1

Firmware files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

12.4.2

Replacing the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

12.5 Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

12.5.1

Actions without enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands