manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 118

Integrated Bus

ID 442289.06

118

Operation manual POSIDYN® SDS 5000

11

WE 

KEEP 

THINGS 

MOVING

Description of the causes

07

hex

The Teleserver concluded remote maintenance.

9

08

hex

The Teleserver rejected the serial number.

10

09

hex

The Teleserver rejected the serial number.

10

0A

hex

An internal error occurred.

5

0B

hex

An internal error occurred.

5

0C

hex

The inverter is waiting for the connection to POSITool.

11

0D

hex

An internal error occurred.

5

0E

hex

An error occurred during flow monitoring between Teleserver and 

inverter.

6

0F

hex

A CRC error was determined for the HTTP response from the 

Teleserver.

7

10

hex

An internal error occurred.

5

11

hex

An error occurred during flow monitoring between Teleserver and 

inverter.

6

12

hex

An error occurred during flow monitoring between Teleserver and 

inverter.

6

13

hex

An internal error occurred.

5

14

hex

An internal error occurred.

5

15

hex

An internal error occurred.

5

Cause no.

Description

1

Establishment of the TCP/IP connection to the Teleserver failed.

Check all network settings and the firewall.

2

The inverter tried to connect with the Teleserver PC, but the specified PC actively 

denied the attempted connection.

Check whether the Teleserver (LAN) was installed correctly and is running. You can 

check the connection to the Teleserver with POSITool, for example.

3

The inverter cannot access the IP address of the Teleserver with the current network 

settings (IP address and subnet mask).

Check the IP address of the inverter and Teleserver.

4

An attempt was made to establish a TCP/IP connection to a Teleserver which already 

exists.

Exit remote maintenance correctly and start remote maintenance again.

5

An internal error was found.

Contact STÖBER ANTRIEBSTECHNIK GmbH & Co. KG, see chapter 1.4 Further 

support.

Error value

Description

Cause no.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands