manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 165

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

16

5

ID 442

289

.06

WE KEEP THINGS MOVING

13

13.3.17 52:Communication

Triggering

Level

Response

Fault counter

Communication malfunction

Fault

Z52

Cause

Description

Measure

Acknowledgement

1:CAN LifeGuard

The device detects the 

Life-Guarding 

event

 (master no longer sends any 

Remote Transmit Request).

Check the CANOpen master.

Switch off/on the Esc key of the 

device at the front of the inverter 

or rising flank of the enable 

signal or programmed 

acknowledgement

2:CAN Sync Error

Sync message was not received within 

the timeout period that is calculated 

from the 

A201 Cycle Period Timeout

 as 

follows:

•

A201

 

≤

 20 ms: 

Timeout period = 

A201

 * 4,

•

20  ms  < 

A201

 

≤

 200 ms: 

Timeout period = 

A201

 * 3,

•

Otherwise: Timeout period = 

A201

 * 

2

•

Make sure that the 

A201

 parameter 

is correctly set.

•

Make sure that the master sends 

the sync message reliably.

Switch off/on the Esc key of the 

device at the front of the inverter 

or rising flank of the enable 

signal or programmed 

acknowledgement

3:CAN Bus Off

The CAN controller in the inverter has 

switched off due to critical and repeated 

CAN bit timing errors. The CAN 

controller is restarted after a waiting 

time of 2 s and acknowledgement of the 

malfunction.

•

Make sure that the CAN baud rate 

was correctly set.

•

Check the wiring.

•

Check the bit timing of a different 

CAN subscriber.

Switch off/on the Esc key of the 

device at the front of the inverter 

or rising flank of the enable 

signal or programmed 

acknowledgement

4:PZD-Timeout

•

Failure of the cyclic data connection 

(PROFIBUS master no longer 

sends) or connection is faulty or

•

PROFINET IO controller no longer 

sends or the connection is faulty

•

Check the PLC (RUN switch, set 

cycle time).

•

Check the wiring.

Switch off/on the Esc key of the 

device at the front of the inverter 

or rising flank of the enable 

signal or programmed 

acknowledgement

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands