Stober POSIDYN SDS 5000 Operation Manual Download Page 33

Page: 33 / 196

Parameterize

Operation manual POSIDYN® SDS 5000

ID 442289.06

KEEP

THINGS

MOVING

The parameter menu of the inverter is divided into menu groups. The menu groups are arranged in

alphabetical order, beginning with the group A.. Inverter, B.. Motor, C.. Machine, and so on. Each menu group

contains a list of parameters which are identified by the letter of the group and a consecutive number such as

A00

A01

A02

, etc. To change a parameter, proceed as shown below. Use the Enter key

to go from the

operation indicators to the menu level.

Fig. 4-3: Menu structure

The menu groups are selected with the arrow keys

and activated with

. Use the

keys to

select the desired parameter within the menu group. You can switch back and forth between the elements in

an array parameter with the

keys. A parameter is then activated for change with

. The value

flashes to indicate that it can be changed with

. The

keys can be used to select which decade

(ones, tens, hundreds, and so on) is to be adjusted. The value is then accepted with the

key or reset with

the

key. Use the

key to access a higher menu level. To save safe from power failure, all changes must

be stored with the

A00 save values

1:active

3000 rpm 1.3A
4: Enabled

B..
Motor

A..
Inverter

C..
Machine

B26 Motor encoder
3: X140

B26 Motor encoder

3: X140

Accept change

Reject change

Value
flashing

B20 Control mode
0: V/f control

....

Betriebs-
anzeige

Parameter

groups

Parameter
selection

Parameter

entry

ESC

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands