manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 61

Parameterizing brake data

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

61

7

7.8

Brake grinding function

The control unit can activate the brake grinding function separately for each of the two brakes. Use action 

B301

 for brake 1 and 

B302

 for brake 2. We will now describe action 

B301

 for brake 1. The description also 

applies to brake 2.

During the brake grinding function, the brake is repeatedly applied for approx. 0.7 s and then released for 

approx. 0.7 s while the motor is rotating with approx. 20 rpm. This grinds off any deposits from the friction 

surface which may affect the halting function. You can parameterize the following settings:

•

How often the brake is applied (

B308

) during rotation.

•

How often the drive is to rotate in each direction (

B309

).

•

Whether one direction of rotation is inhibited (

B306

).

WARNING!

Danger of personal injury or property damage due to defective motor halting brake. Starting the brake 
test action releases the motor brakes one after the other. During the encoder test and/or in the case 
of a faulty brake, the drive axis may move. 

Please take special precautionary measures - above all for gravity-stressed axes.

WARNING!

Danger due to movement of the drive. During the action, the motor rotates at approx. 20 Rpm and with 
the torque entered in 

C03

 or 

C05

. 

Ensure the following.

Before the function starts, make sure the drive is in a position in which it is permissible for it to move at 

this speed and torque.

Restrict the direction of rotation in 

B306

 if the drive is not permitted to rotate in a particular direction.

Check 

E62

 and 

E66

 to see whether other torque limits are also in effect.

Information

Please note that the brake grinding function is defined for the STOBER system (gear motor with 

brake and, if applicable ServoStop). For example, you cannot use the brake grinding function with 

brakes that are attached to the output power of the gear unit. It is essential to clarify the technical 

demands on a system from another manufacturer before you use this function.

Information

During the 

brake grinding

 action, the cycle time is set internally to 32 ms. The change occurs when 

the action is activated. After the action is concluded, the previous cycle time is used again.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands