manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 154

Diagnosis

Operation 

manual 

POSIDYN® 

SDS 

5000

15

4

ID 44

22
8

9

.0

6

WE KEEP THINGS MOVING

13

27:X4-AX5000 gef

A functional AX 5000 option was 

found at X4 although the 

incremental encoder or EnDat 

encoder was parameterized or no 

EnDat encoder is connected to 

option AX 5000.

•

Check the setting of the 

H00

 parameter.

•

Check the connection of the encoder at the POSISwitch 

AX 5000.

Programmed 

acknowledgement

28:X4-EnDatfound

An EnDat encoder was detected at 

X4 although a different encoder was 

parameterized.

Check the setting of the 

H00

 parameter.

Programmed 

acknowledgement

29:AX5000/IncEnc

A faulty POSISwitch AX 5000 option 

at X4 or a wire break in the A-

channel for an incremental encoder 

was detected.

•

Replace the AX 5000 option.

•

Check the encoder cable of the incremental encoder.

Programmed 

acknowledgement

30:Opt2 incomp

Option 2 is not the latest version.

Install the latest version of the option board.

Programmed 

acknowledgement

31:X140EnDatAlar

The EnDat encoder at X140 reports 

an alarm.

Replace the motor.

Programmed 

acknowledgement

32:X140EnDatCRC

Errors accumulate during data 

transfer. The encoder is not 

available.

•

Make sure that the correct encoder type is connected.

•

Check the connection and shielding of the encoder 

cable.

•

Reduce the electromagnetic interference.

Programmed 

acknowledgement

33:IGB Angle dif.

G297

 exceeded on the IGB

•

Check the parameterization of G297.

•

Check the producer.

Programmed 

acknowledgement

Cause

Description

Measure

Acknowledgeme
nt

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands