manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 34

Parameterizing motor data

ID 442289.06

34

Operation manual POSIDYN® SDS 5000

5

WE 

KEEP 

THINGS 

MOVING

5

Parameterizing motor data

For the correct operation of the motors, you must enter the characteristic data and control mode. There are 

several options available to enter the motor data:

•

Selection of a STOBER standard motor in the configuration wizard

•

Use of an electronic nameplate for servo motors with absolute value encoder

•

Direct entry in the parameter lists for motors from other manufacturers or special motors

Information

Refer to the inverter’s projecting manual of the inverter for information on connection, see section 

1.3 Further documentation.

Information

The number of parameters displayed on the inverter and in the POSITool depends on the access 

level set in the parameters. The access level in the inverter can be set in the parameter 

A10

 and 

in POSITool in Tools/Change access level.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands