manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 160

Diagnosis

Operation 

manual 

POSIDYN® 

SDS 

5000

16

0

ID 44

22
8

9

.0

6

WE KEEP THINGS MOVING

13

13.3.11 41:Temp.MotorTMS

Resolution

Level

Response

Fault counter

Motor temperature sensor 

reports overtemperature 

(connection clamp X2).

Warning and malfunction can 

be parameterized in 

U15.

The parameterized malfunction reaction in the 

A29

 

parameter.

Z41

Possible cause

Test

Measure

Acknowledgement

The motor temperature 

sensor is not connected.

Check whether the motor temperature 

sensor is connected to X2 and whether 

the wiring is OK.

Connect the cable properly.

Switch the device on/off or 

programmed 

acknowledgement

The motor is overloaded

Check whether the operating conditions 

have caused the motor to overheat (load 

state, ambient temperature of the motor, 

etc.).

•

Check and, if necessary, correct the 

drive design.

•

Check whether a blockage caused 

overheating.

The KTY evaluation is 

activated although an A-

device is not involved.

Your device indicates a HW version of 190 

or lower and 

B38

 is set to 

1: KTY 84-1xx

.

•

If the motor allows it, set 

B38 = 0: 

PTC

.

•

Replace the inverter with an A-device 

(HW version 200 or higher).

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands