Stober POSIDYN SDS 5000 Operation Manual Download Page 188

Page: 188 / 196

Diagnosis

Operation

manual

POSIDYN®

SDS

5000

ID 44

22
8

WE KEEP THINGS MOVING

13.3.42 *ConfigStartERROR remanents lost

13.3.43 *ConfigStartERROR unknown block

Resolution

Level

Response

No flag values are saved.

—

The configuration does not start.

Possible cause

Test

Measure

Acknowledgement

The

A00 Save values

action was not performed.

—

•

Apply a suitable configuration via

POSITool and then save it (

A00

)

•

Replace the Paramodule.

—

Resolution

Level

Response

The versions of configuration and firmware do not

match.

—

The configuration does not start.

Possible cause

Test

Measure

Acknowledgement

The configuration saved in the

Paramodule originates from a

newer inverter firmware that

recognises more system

modules.

—

Apply a suitable configuration or

firmware via POSITool.

—

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands