Stober POSIDYN SDS 5000 Operation Manual Download Page 167

Page: 167 / 196

Diagnosis

peration

man
ual
POSIDYN

SDS

5000

ID 442

289

.06

WE KEEP THINGS MOVING

7:EtherCAT-DcSYN

If the inverter is synchronized to

EtherCAT by means of the Distributed

Clock, the "SYNC 0" synchronization

signal is checked by a watchdog. If this

SYNC 0 signal remains for a certain

time (that cannot be parameterized),

this cause is triggered. This cause can

only be triggered for EtherCAT with

synchronization by the Distributed

Clock.

•

Check the controller.

•

Make sure that the wiring is in

accordance with electromagnetic

interference regulations.

•

Replace the ECS 5000.

•

Please contact our service

department, see section 1.4 Further

support

Switch the device off/on or

programmed acknowledgement.

Note that an action must also

occur in the controller or the

EtherCAT master for complete

acknowledgement.

8:IGB µC failure

The microcontroller for the IGB

communication has failed.

•

Check the wiring for EM-compliant

design.

•

The inverter must be sent in for

repair. Please contact our service

department, see section 1.4 Further

support

Switch the device off/on or

programmed acknowledgement

9:IGB Lost Frame

IGB motion bus: The subscriber has

detected the loss of min. 2 consecutive

data frames (double error). This cause

can only occur when the IGB state =

3:Motion bus

and the motor is powered.

•

Make sure that all inverters in the

IGB network are switched on.

•

Make sure that all connection

cables are plugged in.

Switch the device off/on or

programmed acknowledgement

10:IGB P. LostFr

IGB motion bus: A different subscriber

has detected a double error and

reported this via

A163

. As a result, this

inverter is also faulty with this cause.

This cause can only occur when the IGB

state =

3:Motion bus

and the motor is

powered.

Switch the device off/on or

programmed acknowledgement

Cause

Description

Measure

Acknowledgement

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands