manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 151

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

15

1

ID 442

289

.06

WE KEEP THINGS MOVING

13

13.3.7

37:Encoder

Triggering

Level

Response

Fault counter

Error due to 

encoder

Fault

The motor always coasts except when 

U30 Emergency stop

 is activated. 

Attention: The reference is deleted for positioning applications due to the event 

37:Encoder. Referencing must be repeated after acknowledgement. 

If the encoder is not connected when switching on the control unit power supply, the 

encoder supply is permanently switched off. Acknowledgement is then only possible by 

switching the inverter off and on.

Z37

Cause

Description

Measure

Acknowledgeme
nt

1:Para<>Encoder

Parameterization is not suitable for 

the connected encoder.

Check and correct the H-parameter.

Programmed 

acknowledgement

2:ParaChgOffOn

Parameter change; encoder 

parameterization can not be 

changed during operation

Save and then switch the device off/on so that the change is 

effective.

Programmed 

acknowledgement

4:X4 chan. A/Clk

Wire break track A/Clock

Check the encoder cable and replace if necessary.

Programmed 

acknowledgement

5:X4-chan. B/Dat

Wire break track B/Data

Programmed 

acknowledgement

6:X4-channel 0

Wire break channel 0

Programmed 

acknowledgement

7:X4-EnDatAlarm

Alarm bit of EnDat encoder present. Replace the motor.

Switch device off/

on

8:X4-EnDatCRC

Errors accumulate during data 

transfer.

•

Check the connection and shielding of the encoder 

cable.

•

Reduce the electromagnetic interference.

Programmed 

acknowledgement

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands