manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 169

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

16

9

ID 442

289

.06

WE KEEP THINGS MOVING

13

13.3.18 55:OptionBoard

Resolution

Level

Response

Fault counter

Error when operating with option board.

Malfunction

The parameterized malfunction reaction in the 

A29

 

parameter.

Z55

Cause

Description

Measure

Acknowledgement

1:CAN5000Failure

CAN 5000 was detected, installed and 

failed.

•

Uninstall the option, check the 

contacts and reinstall the option.

•

Replace the option.

Switch the device on/off or 

programmed acknowledgement

2:DP5000Failure

DP 5000 was detected, installed and 

failed.

3:REA5000Failure

REA 5000 was detected, installed and 

failed.

4:SEA5000failure

SEA 5000 was detected, installed and 

failed.

5:XEA5000Failure

XEA 5000 or XEA 5001 was detected, 

installed and failed.

6:InkSim-Init

Incremental encoder simulation on XEA 

could not be initialized. The motor may 

have rotated during initialization.

7:wrongOption

incorrect or missing option board 

(see

E54/E58

 with 

E68/E69

) 

•

Install the projected option.

•

Adjust the projection.

Switch device off/on 

8:LEA5000failure

LEA 5000 was detected, installed and 

failed.

•

Uninstall the option, check the 

contacts and reinstall the option.

•

Replace the option.

Switch the device on/off or 

programmed acknowledgement

9:ECS5000failure

ECS 5000 was detected, installed and 

failed.

•

Uninstall the option, check the 

contacts and reinstall the option.

•

Replace the option.

Switch the device on/off or 

programmed acknowledgement

10:24Vfailure

Failure of 24V supply for XEA 5001 or 

LEA 5000.

Check and, if necessary, correct the 

24V supply of the option.

Switch device off/on 

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands