manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 147

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

14

7

ID 442

289

.06

WE KEEP THINGS MOVING

13

13.3.2

32:Short/gr.int

13.3.3

33:Overcurrent

Resolution

Level

Response

Fault counter

An internal test is performed when the controller 

part power supply is switched on. An existing 

short-circuit causes a malfunction. A requirement 

for triggering this event is for the supply voltage 

to already be present when starting the device.

Malfunction

The inverter cannot be enabled.

Z32

Possible cause

Test

Measure

Acknowledgement

There is an internal device 

fault.

—

Please contact our service department, 

see section 1.4 Further support

Switch the device on/off or 

programmed 

acknowledgement

Triggering

Level

Response

Fault counter

The total motor current exceeds the permitted 

maximum value.

Fault

The motor always coasts except when U30 Emergency 

stop is activated. Any existing brakes are engaged if they 

were not released via 

F100

 independent of the device 

controller.

Z33

Possible cause

Test

Measure

Acknowledgement

Acceleration times too 

short.

Extend the ramps.

Apply this setting for operation.

Switch the device off/on or 

programmed 

acknowledgement

Incorrectly set torque limits 

in the 

C03

 and 

C05

 

parameters.

Set smaller values in 

C03

 and 

C05

.

Apply this setting for operation.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands