manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 51

Parameterizing brake data

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

51

7

7.4

B20 = 2:Vector control

Proceed as follows for parameterization:

You can make these settings with the 

General settings

 assistant on the 

Holding brake

 page:

Fig. 7-3

: General settings

 assistant, 

Holding brake

 page

Parameterize the brake control for 

B20

 = 

2:vector control

1. Activate the brake control in parameter 

F08

.

2. Specify which brakes are connected to the brake module in 

F09

.

3. Enter the time for which the motor should remain magnetized after triggering the braking procedure in 

B27

.

4. In 

B25

, enter the percentage of halt flux that should remain after the time in 

B27

.

5. Enter the time that the brake requires to be set in 

F07

. If you use two brakes at the brake module, enter 

the one with the longer set time.

6. Enter the time that the brake requires to be released in 

F06

. If you use two brakes at the brake module, 

enter the one with the longer release time.

7. Transfer the parameters to the inverter and save them in it.

8. Switch the inverter off and back on again.

You have now parameterized the brake control.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands