manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 109

Integrated Bus

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

109

11

Comply with the following points concerning activated remote maintenance:

•

There must be at least one inverter in the IGB network which is enabled for remote maintenance so that 

the Internet connection can be maintained. When an active Internet connection exists, you can enable or 

disable inverters in the IGB network at all times.

This is done with the signal specified in 

A167 remote service source

.

•

If you are downloading a new configuration via remote maintenance, set the parameters which are 

relevant to remote maintenance the same as for the configuration up to now so that you avoid a premature 

termination of the connection due to errors in the parameterization. This refers primarily to the parameter 

A167 remote service source

 in which the signal which will start remote maintenance is specified..

•

If you are performing a live firmware update via remote maintenance and then start the firmware again 

immediately afterwards, a new start is performed on the inverters. In this case, the remote maintenance 

connection is disconnected.

The entire IGB network is shown in POSITool. The inverters which are not enabled for remote 

maintenance are marked with a red "stop sign." You can use the buttons at the bottom for the inverters 

which are enabled for remote maintenance to

- read data from the inverters

- trigger the sending of data to the inverters

- execute a live firmware update.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands