manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 41

Parameterizing motor data

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

41

5

5.6

Parameterize motor temperature sensor evaluation

Connect the motor temperature sensor at terminal X2. 

Motor temperature sensor connection

Motor windings are monitored thermally using the motor temperature sensors such as PTC thermistors, KTY 

temperature sensors or Pt temperature sensors.

PTC thermistors are thermistors whose resistance changes significantly with the temperature. When a PTC 

reaches its defined nominal response temperature, the resistance increases dramatically, by twice or more 

the original resistance to several kOhms. As PTC triplets are used, one thermistor monitors each phase of the 

motor winding. With 3 thermistors, all 3 phases are monitored which brings about effective motor protection.

On the other hand, KTY or Pt temperature sensors are temperature sensors with characteristic resistance 

curves that follow the temperature linearly. They therefore allow for analog measurements of motor 

temperatures. However, the measurements are limited to one phase of the motor winding, which also restricts 

motor protection considerably compared with PTC triplets. 

In the 

B38 Motor temperature sensor

 parameter, set whether you will evaluate a PTC triplet, a KTY 84-1xx or 

a Pt1000.

B38

 = 

0:PTC

 

B38

 = 

1:KTY 84-1xx

B38

 = 

2:Pt1000

In 

B39 maximum motor temperature

, set the maximum permitted temperature of the motor. If this is reached, 

the 

41:TempMotorTMP

 fault is triggered. 

The motor temperature measured by the KTY or Pt1000 is displayed in 

E12 Motor temperature

.

Information

Note that evaluation of the temperature sensors is always active. If operation without temperature 

sensor is permitted, the connections must be bridged on X2. Otherwise a fault will be triggered 

when the device is switched on.

Information

Note that the evaluation of a Pt1000 is only possible from firmware V 5.6-S. Before using a Pt or 

KTY sensor, note that motor protection is not ensured to the same extent as when monitoring with 

PTC triplet.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands