manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 146

Diagnosis

Operation 

manual 

POSIDYN® 

SDS 

5000

14

6

ID 44

22
8

9

.0

6

WE KEEP THINGS MOVING

13

13.3

Events

13.3.1

31:Short/ground

Triggering

Level

Response

Fault counter

The hardware short-circuit switch-off is active. 

The output current is too high. If there is no 

supply voltage when starting the device, the 

cause may be a device-internal short circuit/

ground fault.

Fault

The motor continues to coast. The brake chopper cuts 

out. Any existing brakes are engaged if they were not 

released via 

F100

 independent of the device controller.

Z31

Possible cause

Test

Measure

Acknowledgement

Interwinding fault

Check the motor.

Replace the motor.

Switch the device off/on or 

programmed 

acknowledgement

Fault in motor cable

Check the cable

Replace the cable.

Connection fault

Check the connection, e.g. whether V or 

W is connected to PE at X20 U.

Correct the connection.

Braking resistor short 

circuit

Check the braking resistor.

Replace the braking resistor.

Device-internal short 

circuit/ground fault

Check whether the fault only occurs when 

enabling the inverter.

Replace the inverter.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands