manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 68

Parameterizing in-/outputs

ID 442289.06

68

Operation manual POSIDYN® SDS 5000

10

WE 

KEEP 

THINGS 

MOVING

All available parameters can be entered in the source parameters.

To be able to poll application status signals, the signals must be allocated to an output (BA, AA, parameter). 

There is a source parameter for each output in which the signals available for the particular application can 

be selected / inscribed. Source parameters 

F61

 and 

F62

 are used for the binary outputs BA1 and BA2 shown 

in the diagram. At the same time, the signal is written in a parameter (

D200

 bit 1 here). This parameter can 

be read from a fieldbus system.

The indicator parameter (

D181

 in the diagram) shows the signal state after handling by the application. It is 

used to check the signal path. The application descriptions specifies for each signal the possible outputs and 

the related selection parameters as well as the fieldbus and indicator parameter.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands