Stober POSIDYN SDS 5000 Operation Manual Download Page 130

Page: 130 / 196

Service

ID 442289.06

130

Operation manual POSIDYN® SDS 5000

KEEP

THINGS

MOVING

12.4

Live firmware update

12.4.1

Firmware files

A folder named Download is created in the POSITool directory when POSITool is installed:

Fig. 12-1: The

Download

folder is in the POSITool directory

The following files are saved in the folder:

•

Download.exe: Use this file to download the firmware for MDS 5000 and FDS 5000. Observe section

12.4.2 for the download procedure:

•

fx..x.mot: Firmware files for FDS 5000.

•

mx..x.mot: Firmware files for MDS 5000.

•

SDS5000x..x.fli: Firmware files for SDS 5000.

The correct .fli file version is assigned to the existing SDS 5000 by POSITool. If the files saved on your PC

can not be combined with the inverter connected with POSITool, you will receive a message. This can occur

when an .fli file of version V 5.4 or V 5.5 is saved in your download folder but you have an A-device available

that requires an .fli file of version V 5.6.

You can find different versions of firmware files on the STOBER Electronics CD. This CD is supplied with the

inverter.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands