manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 153

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

15

3

ID 442

289

.06

WE KEEP THINGS MOVING

13

18:X120-Timeout

No cycle signal was detected from 

the SSI master.

•

Check the connected cable.

•

Check the power supply of the SSI master.

•

Make sure that the settings of all devices in the SSI 

motion bus are matched to each other.

•

Check whether a device is correctly parameterized as 

the SSL master in the SSI motion bus.

•

Check whether the devices in the SSI motion bus boot up 

together.

Programmed 

acknowledgement

19:X4 double 

transmission

Different positions are frequently 

determined at X4 during double 

transmission.

•

Check the connection and shielding of the encoder 

cable.

•

Reduce the electromagnetic interference.

Programmed 

acknowledgement

20:X4-Busy

Encoder has not responded for too 

long.

•

Check the encoder cable.

•

Check whether a suitable encoder is connected.

Programmed 

acknowledgement

21:X4-wire break

A wire break from one or more 

tracks was detected.

•

Check the encoder cable.

Programmed 

acknowledgement

22:AX5000

Acknowledgement for axis 

switchover did not occur.

Check the wiring between the inverter and POSISwitch 

AX 5000.

Programmed 

acknowledgement

23:AX5000required

A POSISwitch AX 5000 was 

projected but not connected.

•

Match the projection of your hardware.

•

Check the connection of the POSISwitch AX 5000.

Programmed 

acknowledgement

24:X120-speed

B297

, 

G297

 or 

I297

 exceeded for 

the encoder at X120

•

Check the connection and shielding of the encoder 

cable.

•

Reduce the electromagnetic interference.

•

Check the parameterization of 

B297

, 

G297

 or 

I297

.

Programmed 

acknowledgement

25:X4-speed

B297

, 

G297

 or 

I297

 exceeded for 

the encoder at X4

Programmed 

acknowledgement

26:X4-noEnc.found

No encoder was found at X4 or a 

wire break was detected at the 

EnDat/SSI encoder.

•

Correct the connection of the encoder.

•

Check the encoder cable.

•

Correct the power supply of the encoder.

•

Check the setting of the 

H00

 parameter.

Programmed 

acknowledgement

Cause

Description

Measure

Acknowledgeme
nt

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands