Stober POSIDYN SDS 5000 Operation Manual Download Page 47

Page: 47 / 196

Parameterizing brake data

Operation manual POSIDYN® SDS 5000

ID 442289.06

KEEP

THINGS

MOVING

Parameterizing brake data

Motors with holding brakes can be connected to the devices oft the 5

generation of STOBER inverters. There

are two ways to activate the brake.

A brake control is integrated in the following applications:

•

Fast reference value with brake activation

•

Comfort reference value

•

Technology controller

•

Command positioning (endless and limited position range)

•

Synchronous command positioning (endless and limited position range)

•

Motion block positioning (endless and limited position range)

•

Electronic cam (endless and limited position range)

You can activate the brake control in parameter

F08

. Further adjustments are made depending on the

selected control mode.

In addition, a signal source can be parameterized in

F100

. The signal for releasing the brake can be given

direct via the source.

F100

is a global parameter and is available in every application.

F08

is set to

0:inactive

, the brake is activated together with system enable

A900

. In this case, the brake

release times and brake application times are ignored.

In the

F08 = 1:active

setting, the current motor torque is saved when the brake is applied. This torque is

applied again when the brake is released. If

F08

is set to

2:Do not save torque

, only the motor magnetization

is established when the brake is released.

As the brake controller parameterization depends on the selected control mode, the following sections are

subdivided accordingly.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands